 | Radio and Electronics (DED Philippinen, 66 p.) |
 |  | (introduction...) |
|  | 1. INTRODUCTION |
| | (introduction...) |
| | 1.1. A TRIAL TO STATE A DEFINITION OF ELECTRONICS |
| | 1.2. A SHORT HISTORY OF ELECTRONICS |
| | 1.3. CLASSIFICATION OF ELECTRONIC DEVICES |
| | 2. PRINCIPLES OF RADIO COMMUNICATION UNICATION |
| | 2.1. BASICAL IDEAS ABOUT COMMUNICATION |
| | 2.2. DEVELOPMENT OF LONG DISTANCE COMMUNICATION |
| | 2.3. FIDELITY AND DISTORTION |
| | 3. TRANSDUCERS |
| | (introduction...) |
| | 3.1. MICROPHONES |
| | 3.2. LOUDSPEAKERS |
| | 3.3. THE TELEPHON SYSTEM |
| | 3.4. PROBLEM OF FREQUENCY RANGES |
| | 3.5. BANDWIDTH |
| | 4. RADIOWAVES |
| | (introduction...) |
| | 4.1. ORIGIN OF RADIOWAVES |
| | 4.2. PARAMETERS OF ELECTROMAGNETIC WAVES |
| | 4.3. PROPAGATION OF RADIOWAVES |
| | 4.4. SPECTRUM OF RADIOWAVES AND BANDS OF RADIOWAVES |
| | 5. MODULATION OF RADIOWAVES |
| | (introduction...) |
| | 5.1. THE AMPLITUDE MODULATION (AM) |
| | 5.2. FREQUENCY MODULATION (FM) |
| | 5.3. SIDEBANDS |
| | 5.4. TRANSMISSION OF RADIOSIGNALS |
| | 6. RECEPTION OF RADIOSIGNALS (AM - TYPE) |
| | 6.1. AERIAL |
| | 6.2. THE TUNED CIRCUIT |
| | 6.3. INCIDENTAL REMARK ON BLOCK DIAGRAMS |
| | 6.4. DETECTOR OR DEMODULATOR |
| | 6.5. POWER SUPPLY |
| | 6.6. AMPLIFIER |
| | 6.7. SUPERHET RECEIVER (the SUPER) |
| | 6.8 INCIDENTAL REMARK ON MIXING FREQUENCIES |
| | 6.9. CONSTRUCTION OF A SUPERHETRADIO |
| | 7. COMPONENTS OF MODERN RADIO RECEIVERS |
| | 7.1.1. HANDLING OF ELECTRONIC COMPONENTS |
| | 7.1.2. HANDLING OF PRINTED CIRCUITS |
| | 7.1.3. DIFFERENTIATION OF COMPONENTS |
| | 8. PASSIVE COMPONENTS |
| | 8.1. RESISTORS ELECTRICAL CHARACTERISTICS |
| | 8.2. CAPACITORS |
| | 8.3. INDUCTORS |
| | 8.4. COMBINATION OF PASSIVE COMPONENTS |
| | 8.4.1. SERIES CONNECTION OF R AND C, OR R AND L |
| | 8.4.2. COMBINATION OF L AND C, RESONANT (TUNED) CIRCUITS |
| | 8.4.3. TUNED CIRCUIT CONNECTED TO AN AC-VOLTAGE |
| | (introduction...) |
| | 8.4.4.1. QUALITY OF TUNED CIRCUITS |
| | 8.4.4.2. BANDWIDTH |
| | 9. ACTIVE COMPONENTS -1- DIODES |
| | 9.1. CHARACTERISTICS OF SEMICONDUCTORS |
| | 9.2. THE PN-JUNCTION OR DIODE |
| | (introduction...) |
| | 9.2.1. PN-JUNCTION CONNECTED TO VOLTAGE |
| | 9.2.2. CHARACTERISTICS OF A PN-JUNCTION OR DIODE |
| | 9.2.3. ZENERDIODE |
| | 10. BLOCKS OF RADIOS / -1- / POWER SUPPLIES |
| | 10.1. GENERAL CONSIDERATIONS |
| | 10.2. TRANSFORMER |
| | 10.3. THE RECTIFIERS. |
| | 10.4. SMOOTHING AND FILTER CIRCUITS |
| | 10.4.1. THE RESERVOIR CAPACITOR |
| | 10.4.2. FILTER CIRCUITS |
| | 10.5. STABILIZATION |
| | 10.5.1. GENERAL REMARKS |
| | 10.5.1.1. LOAD VARIATIONS |
| | 10.5.1.2. INTERNAL RESISTANCE OF VOLTAGESOURCES |
| | 10.5.1.3. PROBLEMS CAUSED BY THE SMOOTHING CIRCUIT |
| | 10.5.5. METHODS OF STABILIZATION |
| | (introduction...) |
| | 10.5.5.1. PARALLEL-STABILIZATION |
| | 10.5.2.2. SERIES STABILIZATION |
| | 11. ACTIVE COMPONENTS -2- / TRANSISTORS |
| | 11.1. CONSTRUCTION OF A TRANSISTOR |
| | 11.2. CHARACTERISTICS OF TRANSISTORS |
| | (introduction...) |
| | 11.2.1 HANDLING OF CHARACTERISTICS OF TRANSISTORS |
| | 11.2.1.1. CONSTRUCTION OF THE STATIC-MUTUAL-CHARACTERISTICS |
| | 11.2.1.2. CONSTRUCTION OF THE DYNAMIC MUTUAL CHARACTERISTICS |
| | 11.2.1.3. CONSTRUCTION OF THE MAXIMUM-POWER-LINE |
| | 12. AMPLIFIERS |
| | (introduction...) |
| | 12.1. STRUCTURE OF A CLASS A AMPLIFIER |
| | 12.2. FUNCTION OF A SIMPLE CLASS A AMPLIFIER |
| | 12.3. ADVANCED CLASS A AMPLIFIER |
| | 12.4. STABILIZATION OF THE QUIESCENT VOLTAGE |
| | 13. CLASS B AMPLIFIERS |
| | 13.1. LIMITS OF CLASS A AMPLIFIERS |
| | 13.2. CLASS B AMPLIFIERS WITH TRANSFORMERS |
| | 13.3. CLASS B AMPLIFIERS WITHOUT TRANSFORMERS |
| | 13.4. POWER AMPLIFIER WITH COMPLIMENTARY TRANSISTORS. |
| | 14. DETECTOR OR DEMODULATOR |
| | 15. AGC-AUTOMATIC GAIN CONTROL |
| | 16. IF-AMPLIFIERS |
| | 17. FEEDBACK |
| | 18. OSCILLATORS |
| | 19. FREQUENCY CHANGERS MIXERSTAGE |
| | 20. DECOUPLING CIRCUITS |
| | 21. MATCHING OF AMPLIFIERSTAGES |
| | 22. COUPLING OF AMPLIFIERSTAGES |
| | 23. RADIO SERVICING |
| | 23.1. IMPORTANCE AND SUBJECT OF FAULT FINDING |
| | 23.2. FAULTS AND FAULT FINDING |
| | 23.3. FAULT FINDING METHODS |
| | 24. THE USE OF THE OSCILLOSCOPE |
2.3. FIDELITY AND DISTORTION
We agreed already: the AIM OF COMMUNICATION is to transport the IDEA (the SIGNAL) totally correctly from the ORIGIN (the TRANSMITTER) to the ADDRESS (the RECEIVER).
But it is easy to imagine, that even in the original way of communication (speaking with each other) very often the idea was not received properly.
As the possibilities of arising faults are increasing with increasing complexity of the system in use, it is easy to understand, that radio technology is mainly a struggle to get a good or at least a satisfying RECEPTION.
The quality of the equivalence of the signal at the start of the communication (INPUT fig. 7a) and the signal at the end of the communicationline (OUTPUT fig 7b or 7c) is called FIDELITY.
fig. 7a
fig. 7b
fig. 7c
The rate of difference between INPUT and OUTPUT is called DISTORTION.
|
|