Cover Image
close this bookIntroduction to Electrical Engineering - Basic vocational knowledge (Institut für Berufliche Entwicklung, 213 p.)
View the document(introduction...)
View the documentPreface
View the document1. Importance of Electrical Engineering
close this folder2. Fundamental Quantities of Electrical Engineering
View the document2.1. Current
View the document2.2. Voltage
View the document2.3. Resistance and Conductance
close this folder3. Electric Circuits
View the document3.1. Basic Circuit
View the document3.2. Ohm’s Law
close this folder3.3. Branched and Unbranched Circuits
View the document3.3.1. Branched Circuits
View the document3.3.2. Unbranched Circuits
View the document3.3.3. Meshed Circuits
close this folder4. Electrical Energy
View the document4.1. Energy and Power
View the document4.2. Efficiency
View the document4.3. Conversion of Electrical Energy into Heat
View the document4.4. Conversion of Electrical Energy into Mechanical Energy
close this folder4.5. Conversion of Electrical Energy into Light
View the document4.5.1. Fundamentals of Illumination Engineering
View the document4.5.2. Light Sources
View the document4.5.3. Illuminating Engineering
View the document4.6. Conversion of Electrical Energy into Chemical Energy and Chemical Energy into Electrical Energy
close this folder5. Magnetic Field
View the document5.1. Magnetic Phenomena
View the document5.2. Force Actions in a Magnetic Field
close this folder5.3. Electromagnetic Induction
View the document5.3.1. The General Law of Induction
View the document5.3.2. Utilisation of the Phenomena of Induction
View the document5.3.3. Inductance
close this folder6. Electrical Field
View the document6.1. Electrical Phenomena in Non-conductors
close this folder6.2. Capacity
View the document6.2.1. Capacity and Capacitor
View the document6.2.2. Behaviour of a Capacitor in a Direct Current Circuit
View the document6.2.3. Types of Capacitors
close this folder7. Alternating Current
View the document7.1. Importance and Advantages of Alternating Current
View the document7.2. Characteristics of Alternating Current
View the document7.3. Resistances in an Alternating Current Circuit
View the document7.4. Power of Alternating Current
close this folder8. Three-phase Current
View the document8.1. Generation of Three-phase Current
View the document8.2. The Rotating Field
View the document8.3. Interlinking of the Three-phase Current
View the document8.4. Power of Three-phase Current
close this folder9. Protective Measures in Electrical Installations
View the document9.1. Danger to Man by Electric Shock
close this folder9.2. Measures for the Protection of Man from Electric Shock
View the document9.2.1. Protective Insulation
View the document9.2.2. Extra-low Protective Voltage
View the document9.2.3. Protective Isolation
View the document9.2.4. Protective Wire System
View the document9.2.5. Protective Earthing
View the document9.2.6. Connection to the Neutral
View the document9.2.7. Fault-current Protection
View the document9.3. Checking the Protective Measures

3.1. Basic Circuit

If an incandescent lamp for illuminating a working place is to be caused to light, the following pre-conditions are required.

· A voltage source whose voltage is available at the point of connection (socket outlet). The voltage source may be far away from the point of connection (e.g. in a power station). A fuse is interposed in each line as overcurrent protection.

· A 2-core line leading to the incandescent lamp which conducts the voltage via a plug to the lamp. For conveniently switching on and off, a switch is interposed. Fig. 5.1. shows the described arrangement. Fig. 5.2 the schematic representation with symbols which is called wiring diagram.

Fig. 3.1. Simplified representation of the arrangement voltage source/table lighting fitting

1 - Voltage source
2 - Table lighting fitting
3 - Plug socket
4 - Plug
5 - Fuses
6 - Switch

This shows that a closed connection from the voltage source to the incandescent lamp is essential for operation. The charge carriers driven from the source pass through the conductor, transfer their energy to the lamp and return to the source where they receive again drive energy. This is a circulatory process and, therefore, such an arrangement is called circuit.

Fig. 3.2. Wiring diagram for Fig. 3.1

Graphical symbols:

1 - Voltage source
2 - Lighting fitting
3/4 Plugged connections
5 - Fuses
6 - Switch

Since no charge carriers are lost during the passage, the current is a phenomenon closed in itself, a band without start and without end which has the same intensity at any point.

The above described example is the simplest circuit. Therefore it is called basic circuit. For the principle illustrated here it is of no consequence if in the place of the generator a different voltage source (e.g. an accumulator) is used and a heater, washing machine, motor or another consumer operates in the place of the electric bulb. In the circuit diagram, frequently the fuses, the point of connection and the switch are not represented; the consumer is frequently represented simply by the resistance symbol, see Fig. 3.3.

Fig. 3.3. Fundamental circuit

1 - Voltage source
2 - Load general

The basic circuit is a circuit which cannot be further simplified. It consists of a voltage source to which a consumer is connected. The current flowing in this circuit is a phenomenon closed in itself, a band without start and end which has the same intensity at any point.