Cover Image
close this bookMushroom Cultivation in Thailand (Peace Corps, 1987, 85 p.)
close this folder4. Straw mushroom cultivation in beds
View the document(introduction...)
View the documentMaterials needed
View the documentCultivation steps
View the documentHarvesting
View the documentCultivation in rainy season

Cultivation steps

The steps required in the cultivation of straw mushrooms are as follows:

1. Soak the rice straw or dried water hyacinth overnight in water for best results during the cold and hot seasons. During the rainy season, it is possible to soak the straw for only 15-20 minutes and achieve good results, although a longer soaking period is preferable.


Figure 19: Soaking Rice Straw

2. Prepare the soil where the beds are to be made by spading an area approximately 120 cm wide 6-8 cm deep and 7 meters long. Expose this area to the sun for 3-4 days in order to kill any existing bacteria and/or fungi. During the rainy season construct a raised bed 5-10 cm above the surrounding soil level to prevent flood damage during heavy rains.

3. Place the wooden mold at one end of the prepared soil area and sprinkle the supplementary food around the inside border of the mold, creating a band of food approximately 6-8 cm wide and 1 cm thick.

4. Sprinkle one-third of a bag of straw mushroom spawn on the supplementary food, placing the majority of the spore next to the inside border of the wooden mold.


Figure 20: Bed Preparation

(Note: In this example, a bed composed of three layers is being made. Hence, the use of one-third of a bag of spawn per layer. If the bed was composed of four layers, one-fourth of a bag of spawn would be used per layer. Five layers would require one-fifth of a bag per layer, and so on. Each bed constructed will use a total of one bag of mushroom spawn).

5. Place the presoaked rice straw or water hyacinth on top of the spawn-supplementary food layer. Press the straw or water hyacinth firmly into the bottom of the mold, filling the mold one-third full. This completes the first layer of the bed.

6. Repeat this procedure to complete subsequent layers, then water thoroughly with one or two buckets of water. The number of layers planted in one wooden mold varies according to the season: three layers in the hot season, four layers in the rainy season, and five layers in the cold season.

7. Remove the wooden mold and place it next to the first bed, lengthwise, leaving 12-16 cm between beds in the hot season and 8-10 cm in the cold and rainy seasons. Use the described method to plant as many beds as desired. Ten beds of straw mushrooms are commonly planted in one 7-meter row.

8. Loosen the soil between and around the beds in the row. Sprinkle supplementary food over this area and water thoroughly. Sprinkle one bag of straw mushroom spawn over the supplementary food between and around the beds in the ten-bed row.


Figure 21: Covering Straw Mushroom Beds

9. Cover the beds with two sheets of clear plastic, overlapping the sheets in the middle of the beds. Be careful not to let the plastic sheets rest against the sides of the bed as this will inhibit mushroom growth and greatly reduce mushroom production. Bamboo sticks can be used as supports to keep the sheets from coming in contact with the sides (and tops, if desired) of the beds. Wood, rocks and/or dirt should be used to secure the edges of the plastic sheets to the ground (see Figure 21).

10. Cover the plastic sheets with dry rice straw, as shown in Figure 22. This will prevent direct sunlight from shining on the beds which is likely to kill the spawn. If desired, an additional roof of coconut leaves (or other suitable material) can be built over the beds to further protect them from excessive exposure to sunlight and heat. This roof should be built high enough above ground level to allow people to walk comfortably under it.


Figure 22: Protection for Cultivation Beds

11. Check the moisture content of the beds on day 4. This is done by taking a sample of rice straw from one of the beds (one or two pieces of straw is adequate, examine samples from several areas in the row of beds) and twisting it. If much water drips from the straw sample, the beds are too wet and need to be dried. This is done by opening the plastic sheets over the middle of the beds, leaving an open space 5-10 cm wide, the length of the row. This will allow air to circulate within the row, thereby decreasing moisture content. It is best to open the plastic sheets for 5-15 minutes during the early morning and/or late evening, when the sun is low in the sky. This procedure reduces the chances of sunlight-induced spawn kill.


Figure 23: Checking Moisture Content of Straw

If 2-4 drops of water slowly fall from the twisted straw samples, the beds have adequate moisture. If no water drips from the straw, the beds are too dry and require watering. When watering, be careful to water around, not on, the beds.

12. If the weather is extremely hot (35°C and higher) during the first five days after planting, open the plastic sheets over the middle of the beds leaving an open space 5-10 cm wide the length of the row, as shown in Figure 24. This will allow air to circulate slowly within the row and prevent the spore from dying due to high temperatures. If the plastic sheets are opened, the moisture content of the beds should be closely monitored using the technique described in step 11.


Figure 24: Opening Plastic Sheet for Ventilation

13. White thread-like mycelium and possibly small mushrooms might be seen growing in the beds after 5-8 days.